KIT-RF04-CM02-900 (US) -- CM02-RF04 Telemetry Pair for USA (900MHz) ...US$192.00 KIT-RF04-CM02-400 (EU) -- CM02-RF04 Telemetry Pair for Europe (433MHz) ...US$192.00
The RF04 is a very easy to use radio telemetry module set for your I 2C devices. The main module is powered from the USB bus, so it needs no external power supply or batteries. Just plug it into your PC and it will appear as a COM port. The RF04 module set can be used by anyone who can program a PC to use the COM ports.
The CM02 module, together with its companion RF04 module , form a complete interface between your PC and our range of I 2C modules. You can send commands down to your robot and receive telemetry data back up to the PC. Now you have all the modules necessary to control your robot from your PC. The CM02 is powered from your robots battery, which can be anything from 6v to 12v. The CM02 can monitor battery voltage and report this back to the PC (so your robot knows when its hungry!). There are four I 2C connectors on the CM02, but is not limited to four I 2C devices. In practice, you may only need one connector and route the I 2C bus around all the modules you wish. Bit rate on the I 2C bus is approximately 100KHz.
Here is RF04 and CM02 datasheet.
The RF04-900 uses the LPRS EasyRadio ER900TRS transceiver for EU (868-870MHz) or USA (902-920MHz) markets. Power output up to 10mW.
RF04 Specifications:
Power Requirement - Powered entirely from USB port
Over Air Data Rate - 19200 bps.
Default Frequency - RF04-400 (EU) 433.92MHz
- RF04-900 (USA) 869.85MHz
Range - Up to 250m line of site, Up to 150m for RF04/900
Data Buffer - Internal 128 byte buffer
CM02 Specifications:
Power Requirement - 6v - 12v Battery
Over Air Data Rate - 19200 bps.
Default Frequency - CM02-400 433.92MHz
- CM02-900 869.85MHz
Range - Up to 250m line of site, Up to 150m for CM02/900
Use with - Any I 2C device
KIT-CM02-900 (US)-- CM02 Radio Communication Module for USA (900MHz) ...US$99.95
KIT-CM02-400 (EU)-- CM02 Radio Communication Module for Europe (433MHz) ...US$99.95
 
The CM02 module, together with its companion RF04 module , form a complete interface between your PC and our range of I 2C modules. You can send commands down to your robot and receive telemetry data back up to the PC. Now you have all the modules necessary to control your robot from your PC. The CM02 is powered from your robots battery, which can be anything from 6v to 12v. The CM02 can monitor battery voltage and report this back to the PC (so your robot knows when its hungry!). There are four I 2C connectors on the CM02, but is not limited to four I 2C devices. In practice, you may only need one connector and route the I 2C bus around all the modules you wish. Bit rate on the I 2C bus is approximately 100KHz. Here is the datasheet .
CM02 Specifications:
Power Requirement - 6v - 12v Battery
Over Air Data Rate - 19200 bps.
Default Frequency - CM02-400 433.92MHz
- CM02-900 869.85MHz
Range - Up to 250m line of site, Up to 150m for CM02/900
Use with - Any I 2C device
KIT-RF04-900 (US)-- USB Telemetry Module for USA (900MHz) ...US$99.95
KIT-RF04-400 (EU)-- USB Telemetry Module for Europe (433MHz) ...US$99.95
 
The RF04 is a very easy to use radio telemetry module set for your I 2C devices. The main module is powered from the USB bus, so it needs no external power supply or batteries. Just plug it into your PC and it will appear as a COM port. The RF04 module set can be used by anyone who can program a PC to use the COM ports. Here is the datasheet .
RF04 Specifications:
Power Requirement - Powered entirely from USB port
Over Air Data Rate - 19200 bps.
Default Frequency - RF04-400 (EU) 433.92MHz
- RF04-900 (USA) 869.85MHz
Range - Up to 250m line of site, Up to 150m for RF04/900
Data Buffer - Internal 128 byte buffer
KIT-GPS-- Global Positioning System (GPS) ...US$425.00
The DS-GPM is a highly integrated Global Positioning System Module. The DS-GPM provides latitude, longitude, heading, altitude, speed, time, date and satellite position in easy to access registers via IIC and RS232 communications. Here is the datasheet .
KIT-14 Buttons IR-Controller ...US$29.00
The kit included IR remote controller, decoder IC and all necessary components. It uses a commercial 14-button remote control unit to put an active low signal on one of 14 pins on a decoder IC. All necessary components and circuit diagram for building a decode circuit with a decoder IC are provided with the kit. Great to build your own IR remote Robot by interfacing the robot controller with this kit.
KIT-RF-TXRX434MHz-A-- TWO buttons RF Transmitter and Receiver Module ...US$39.50
The RF transmitter and receiver comes ready-made in a case with a 12V battery. The frequency used is 434MHz. It has a and receiver range of 40-50 meters. The kit includes two-button transmitter module, a RF receiver module, all necessary documents.
KIT-RF-TXRX434MHz-B-- FOUR buttons RF Transmitter and Receiver Module ...US$39.50
The RF transmitter and receiver comes ready-made in a case with a battery. The frequency used is 434MHz. It has a and receiver range of 40-50 meters. The kit includes four-button transmitter module, a RF receiver module, all necessary documents.
KIT-UHF-SWITCH-A Two Channels UHF Switch unassembled kit ... US$55.00
KIT-UHF-SWITCH-A-ASSEMBLED Two Channels UHF Switch (Assembled and Tested)... US$63.00
Using the above 2-button RF Transmitter to toggle 2 relays on/off on a RF Receiver PCB. It can transmit up to 50 meters away. 434MHz transmission. The kits include full schematic with all components included. Assembly instruction included.
KIT-UHF-SWITCH-B Four Channels UHF Switch unassembled kit... US$62.50
KIT-UHF-SWITCH-B-ASSEMBLED Four Channels UHF Switch (Assembled and Tested)... US$72.95
Using the above 4-button RF Transmitter to toggle 4 relays on/off on a RF Receiver PCB. It can transmit up to 50 meters away. 434MHz transmission. The kits include full schematic with all components included. Assembly instruction included.
|
